Fluid discrimination incorporating amplitude variation with angle inversion and squirt flow of the fluid

2022-09-23 08:16YuRongWangZhaoYunZongXingYaoYin
Petroleum Science 2022年4期

Yu-Rong Wang , Zhao-Yun Zong ,*, Xing-Yao Yin

aChina University ofPetroleum, Qingdao, Shandong, 266580, China

bShandong Provincial Key Laboratory of Deep Oiland Gas, Qingdao,Shandong,266580,China

cPilotNationalLaboratory for Marine Science andTechnology(Qingdao),Shandong, 266580,China

Keywords:Fluid discrimination Poroelasticity theory Linearized seismic reflectivity Pre-stack seismic inversion Squirt flow of fluid

ABSTRACT Pre-stack seismic inversion is an important method for fluid identification and reservoir characterization in exploration geophysics. In this study, an effective fluid factor is initially established based on Biot poroelastic theory, and a pre-stack seismic inversion method based on Bayesian framework is used to implement the fluid identification. Compared with conventional elastic parameters, fluid factors are more sensitive to oil and gas.However,the coupling effect between rock porosity and fluid content is not considered in conventional fluid factors,which may lead to fuzzy fluid identification results.In addition,existing fluid factors do not adequately consider the physical mechanisms of fluid content,such as squirt flow between cracks and pores.Therefore,we propose a squirt fluid factor(SFF)that minimizes the fluid and pore mixing effects and takes into account the squirt flow. On this basis, a novel P-wave reflection coefficient equation is derived,and the squirt fluid factor is estimated by amplitude variation with offset(AVO) inversion method. The new reflection coefficient equation has sufficient accuracy and can be utilized to estimate the parameters. The effectiveness and superiority of the proposed method in fluid identification are verified by the synthetic and field examples.

1. Introduction

Fluid identification has always been a hot topic in seismic exploration. Reliable fluid identification can improve the exploration success rate and reduce the investment cost,which is of great significance to oil and gas exploration and reservoir evaluation.Seismic fluid identification mainly includes two parts, one is the construction of fluid indicators, the other is the extraction of fluid indicators from seismic data. Direct indicators such as bright and non-bright spots have been widely used in reservoir characterization (Mazzotti, 1990; Ross and Kingman, 1995; Zdanowski and G′orniak, 2014; Wojcik et al., 2016). However, these fluid indicators are very sensitive to any fluid saturation,which will make the interpretation results ambious (Allen et al., 1993; My′sliwiec,2004; Cichoste˛pski et al., 2019). Certain fluid changes can have substantial effects on bright spots and AVO analysis (Batzle et al.,1995). Therefore, it is necessary to extend the definition of hydrocarbon indicator to fluid classification. The construction of conventional fluid factors was originally derived from the elastic parameters of the simplified Zoeppritz equation (Zoeppritz and Erdbebenwellen, 1919) and extracted from pre-stack seismic data. Smith and Gidlow (1987) defined the fluid factor and developed a weighted stacking method for gas reservoir detection using the amplitude variations with offset(AVO)theory.By studying the tensile properties of underground strata, Goodway et al. (1997)discovered a new fluid factor λρ and μρ (Lame parameters × density) to identify the fluid type of the reservoir. Based on the pore elasticity theory of porous elastic medium, Russell et al. (2003)defined ρf to reflect the pore fluid type. Russell et al. (2011)further defined the Gassmann fluid terms f as a fluid factor and extended the linearized AVO approximation. Due to the mixing effect of fluid and pore, these fluid indicators have the solid-liquid coupling fluid identification illusion problems. Yin and Zhang(2014) proposed a new AVO approximate reflectivity equation to estimate the effective pore-fluid bulk modulus,avoiding the strong nonlinearity between seismic data and fluid bulk modulus. Zong et al. (2015) introduced a new linear P-wave reflection coefficient equation in terms of fluid modulus (FM). FM was affected only by fluids and not by physical properties of rocks such as porosity.Based on the classical fluid indicator, Zhang et al. (2016) constructed a new fluid indicator by considering the squirt flow effect between rock pores and cracks. In addition, different unconventional fluid indication construction methods and corresponding fluid identification strategies were proposed.Shaw and Sen(2006)presented a method for estimating fluid indicators using fullazimuth AVOA (amplitude-versus-offset-and-azimuth) data. Liu and Ghosh (2017), based on the Gassmann-Biot theory, proposed a new seismic attribute J to reduce the uncertainty of oil and gas prediction in the case of different porosity.

The squirt flow mechanism that causes seismic wave attenuation and velocity dispersion contains the relevant information of fluid and skeleton in the actual reservoir.The introduction of squirt flow in fluid discrimination can reduce the false bright spots and the uncertainty of seismic exploration (Barak et al., 2018). The conventional fluid factor is only based on the assumption of uniform pore distribution and neglects the effect of the “local flow”action on the pore scale (O'Connell and Budiansky,1977). Underground rock media contains a large number of pores and cracks,which are essential for the occurrence of oil and gas (Wu et al.,2015; Kumar et al., 2018, 2019; Kumari et al., 2021; Kumari and Kumar, 2020). When pores and cracks coexist, the aspect ratio of crack is much smaller than that of pore.Under the action of external stress, the pore fluid will be squeezed from cracks into pores and this local flow is called“squirt flow”.This squirt flow is considered to be an important cause of velocity dispersion and energy attenuation of seismic wave in fluid-bearing rocks(Mavko and Nur,1975;Murphy et al., 1986; Wojcik et al., 2016; Zong and Wang, 2019).Tang (2011) analyzed the squirt effect in detail and proposed a unified theory of elastic wave propagation. On basis of the unified theory,a kind of squirt fluid factor(SFF)considering the squirt flow is established to improve the precision of fluid discrimination.

Seismic inversion method is an important tool for accurately estimating fluid factor from seismic reflection data (Shuey, 1985;Downton, 2005; Skopintseva et al., 2011; Kumari et al., 2017; Li et al., 2020; Kumar and Kumari, 2020). According to the approximate orders and optimization methods of reflection coefficient equation,seismic inversion can be divided into nonlinear and linear AVO inversion. Nonlinear AVO inversion is based on the exact or high-order reflection coefficient equation(Gholami et al.,2018).Yin et al.(2016)used the high-order Zoeppritz approximation equation to solve AVO problems in the trust region by applying the inverse operator estimation algorithm. In order to overcome the nonuniqueness problem, Mollajan et al. (2019) used imperialist competitive algorithm optimization method to solve nonlinear AVO inversion. Linear AVO inversion methods are generally based on linear reflection coefficient equation. Although AVO linear approximation equation is limited to approximation conditions, it plays an important role in fluid identification due to its efficiency and stability(Downton and Ursenbach,2006;Tor et al.,2008).The Bayesian formula establishes the quantitative relationship between the posterior probability distribution of model parameters and the prior distribution and likelihood function(Dashti and Stuart,2016;Lang and Grana,2018;Zhang et al.,2019).Prior distribution can be selected according to the actual situation, such as Huber distribution, Cauchy distribution, Gauss distribution, etc. Compared with the conventional Gaussian probability distribution, Cauchy distribution has long tails and could generate sparse solutions (Zhang et al., 2018). Therefore, Cauchy distribution is selected as the prior information of inversion to make the inversion results more stable and high-resolution.

In this study, we focus on the construction approach of fluid factors and the prediction approach of the fluid factor from prestack seismic data. A fluid discrimination approach method combining the unified theory of porous media with cracks and Bayesian AVO inversion is proposed. Firstly, we start by building a squirt fluid factor (SFF) based on a unified theory. The squirt flow due to the uneven distribution of pores and cracks will cause deviation of fluid identification, and the squirt fluid factor (SFF) can take the effect of squirt flow into consideration.Secondly,we derive a novel reflection coefficient in terms of SFF.Finally,the parameters are solved in the Bayesian frame for the higher stability and accuracy. The application of model and field data demonstrates the robustness and effectiveness of the proposed method.

2. A cracked porous medium elastic wave theory

The rock medium usually contains both pores and cracks,which have an important effect on the elastic wave propagation. On the basis of Biot's poroelastic wave theory, Tang (2011, 2012) introduced the influence of cracks and proposed a unified elastic wave theory. The cracked porous medium wave theory can simulate the attenuation and dispersion of elastic wave caused by squirt flow.And crack density and aspect ratio are introduced as two important parameters to describe porous rocks with cracks.

For a porous rock modeled by Biot's theory, the mass conservation of fluid in porous rock follows

where U is fluid displacement, u is solid displacement, ρfis fluid density, φ is porosity, P is pore fluid pressure, subscripts x and t indicate partial derivatives,c0is acoustic velocity in fluid,Kdis dry bulk modulus of the solid,Ksand Kfis the bulk modulus of the solid grain and of the pore fluid respectively.

Tang et al. (2012) introduces cracks into the porous rock and squirt flow between cracks and pores occurs. The pore fluid pressure is affected by the squirt flow,which depends on the amount of fluid flowing into and out of the pore space. In the porous rock containing flat-or narrow-shaped cracks,the pore fluid pressure is

In a unit volume of rock, the increment of fluid expansion in pore space caused by local fluid flow is qv.η is viscosity coefficient,ε is crack density,μ,σ and Kgare shear modulus,Poisson's ratio and bulk modulus of background medium in the absence of squirt flow.ω=2πfre is angular frequency,fre is dominant frequency of seismic in the work area.

3. The extension of poroelastic theory

In the Biot theory, there are three kinds of waves that can propagate in fluid-filled porous media, fast compressional wave,shear wave and slow compressional wave.Fast compressional wave and shear wave are mainly related to the elasticity of solid skeleton and pore fluid.Slow compressional wave is affected by the fluid and skeleton motion(Biot,1956a,b).The main factors affecting seismic reflection characteristics include the velocity of seismic wave and density of medium. And the situation becomes more complicated when medium contains pore and fluid. The effects of fluid saturation can be described by Gassmann equation. According to the poroelastic theory, the P-velocity Vpand S-velocity Vsunder the low frequency condition are defined as,

From Eq.(12)we can know that Russell fluid factor f is not only affected by fluid but also the dry rock bulk modulus, rock matrix modulus and porosity. However, porosity easily causes considerable ambiguity in fluid identification(Yu et al.,1993).Therefore,it's necessary to diminish the porosity impact on fluid indicator and reduce ambiguity.

The Biot-consistent theory introduce the effect of crack by Kd,

In Eq.(19),ε is crack density,φcis volume fraction of crack,γ is aspect ratio of crack,μsis shear modulus of matrix.Substituting Kdof Eq.(18)into Eq.(11)and we can describe the influence of pores and cracks on the elastic properties of media. However, to extend this influence into frequency domain,we must take the squirt flow effect into consideration.

According to the derivation of Gassmann formula, Tang (2011)proposed a new rock physical equation which maintains both the basic characteristics and structure of Biot theory(Eq.(21)).Compared to Eq.(11),Eq.(21)adds a contribution item S(ω)to characterize the squirt flow.We define S(ω)as a term representing the contribution of the squirt flow and define S as a total squirt flow effect item.

By incorporating total squirt flow effect item and Russell fluid factor, fsis generated (Zhang et al., 2016). It retains the original characteristics and structure of the conventional fluid factor and also reflects the influence of the squirt flow effect on the wave propagation. However, to diminish porosity impact on fluid indicator, we further establish a solid - liquid decoupling fluid factor considering squirt flow effect (SFF).

Referring to Eq. (17),

Kfsis the proposed squirt fluid factor (SFF). We generate Kfsby incorporating total squirt flow effect item S and fluid modulus Kf.The new factor reflects the comprehensive response of fluid modulus and squirt flow in the form of elastic parameter.

Fig.1 demonstrates the influence of different parameters on the squirt flow effect S.Fig.1 shows that S item decreases with increasing frequency, illustrating that this local flow squeezes at lower frequency and gets locked at high frequency. Just as Mavko and Jizba(1991) pointed, this kind of squirt flow occurring on local small scale depends heavily on frequency. From Fig.1(a) we can see that when the crack density is less than a certain value,S varies positively with crack density.But when crack density is greater than a certain value,S decreases.Fig.1(b)displays the variation of S with respect to the viscosity coefficient. As the viscosity coefficient increases, the total squirt flow effect item S becomes smaller.In other words,squirt flow is a kind of viscous motion within the frequency band of seismic exploration and the squirt effects of water and oil are different because the viscosity of them differs.

4. Linearized reflectivity and direct inversion for squirt fluid factor

Amplitude variation with offset (AVO) inversion is a seismic prestack inversion method for estimating fluid and reservoir information. Compared with post-stack seismic inversion, pre-stack seismic inversion allows us to directly estimate various elastic parameters rather than estimating impedance firstly and then calculating elastic parameters indirectly. Russell et al. (2011)derived a generalized AVO approximation by introducing P/S velocity of dry rock to extract fluid, shear modulus and density(f -m-r equation).Eq.(27)is the f -m-r equation proposed by Russell et al. (2011). Using the unified theory proposed by Tang(2011), we re-express the f -m-r equation and formulate a new reflection coefficient approximation with squirt fluid factor Kfs.

Fig.1. Analysis of the influence of different parameters on the squirt flow effect. (a) crack density (b) viscosity coefficient.

Fig. 2. (a) The real well-log data. (b)The comparison of Russell fluid factor (blue) and squirt fluid factor (red) on well log.

θ is incident angle, m1represents the elastic parameters upper the reflection interface and m2represents the parameters below the reflection interface, respectively. By introducing total squirt flow effect item into the equation, we can estimate the fluid modulus in the coexistence of pores and cracks. And we can take two important parameters of crack into consideration, crack density and crack aspect ratio.This new reflection coefficient equation is derived with the following assumptions including plane waves,small incident angle range and small relative changes in elastic parameters occur across the boundary.

To verify the accuracy of Eq. (31), we set three models containing P-velocity Vp, S-velocity Vs, density ρ, porosity φ, crack density ε and crack aspect ratio γ as shown in Table 1.Model 1 is a dry reflector.The porosity of each layer is equally 16%and the upper P-impedance is smaller than the lower layer.Model 2 is a dry-water reflector. The upper layer is dry sand layer and the porosity is 16%while the lower layer is water sand and the porosity is 18%.Model 3 is water-gas reflector. The pore fluid is different and porosity are different.In these three models,we set the crack density as 0.15 in dry sand and 0.2 in fluid sand to calculate the squirt fluid factor Kfs.Fig. 3 shows the comparison of different reflection coefficient curves. Curves in blue, black and red denote the reflection coefficients calculated from the exact Zoeppritz equation, Aki-Richards approximate equation and Eq. (31) respectively. Fig. 3(a)displays the comparison of reflection coefficient curves calculated by exact Zoeppritz equation (blue curve), Aki-Richards approximate equation (black curve) and proposed equation (red curve) of model 1. Fig. 3(c) displays the comparison of reflection coefficient curves respectively calculated by exact Zoeppritz equation (blue curve), Aki-Richards approximate equation (black curve) and proposed equation (red curve) of model 2. Fig. 3(e) displays the comparison of reflection coefficient curves calculated by exact Zoeppritz equation (blue curve), Aki-Richards approximate equation (black curve) and proposed equation (red curve) of model 3.Fig. 3(b, d, f) show the difference between reflection coefficients from the exact Zoeppritz equation and Eq. (31) of three models,respectively.In model 1,the AVO curve calculated by Eq.(31)is very close to the AVO curve calculated by the Zoeppritz equation and the Aki-Richards approximation. Because the derivation of Eq. (31)begins with the Aki-Richards approximation, the two equations give similar AVO curves in dry reflector. In model 2, AVO curves calculated by Aki-Richards approximation and Eq. (31) are almost the same, and both curves are close to Zoeppritz curve when the incidence angle is less than 30°. However, as the incidence angle increases, the AVO curves calculated by the Aki-Richards approximation and Eq. (31) deviates from those by Zoeppritz equation.Because the density of the upper and lower layers is different due to the change of porosity,besides,the effect of porosity on velocity is greater than that of pore fluid. Thus, at large incident angles,porosity differences lead to large variations in P-wave and S-wave velocities,resulting in large errors between the AVO approximation and the precise Zoeppritz equation. In model 3, we note that the AVO curves calculated by Eq. (31) and the Aki-Richards approximation are almost identical, and both are very close to those by Zoeppritz equation in the range of incident angles less than 30°.However,when the incident angle is large,the two curves do not fit with Zoeppritz curve. This is because the change of fluid content and porosity leads to the larger change of P-velocity and S-velocity,which makes the AVO approximation less effective at large incident angle. To summarize, from these figures we can see that although the red curve is not exactly identical with two others,they are very close,especially when the incident angle is less than 30°.Therefore,the new reflection coefficient is reasonably feasible and accurate.And because the incident angle of practical seismic exploration is usually less than 40°, we can conclude that the new reflection coefficient equation can be utilized to invert the fluid factor stably in practical applications.

To find out whether the elastic parameters can be well estimated from pre-stack seismic data,we analyze the contribution of each parameters to the reflection coefficient. Fig. 4 shows the reflection coefficient of Eq.(31)in terms of five parameters such as squirt fluid factor Kfs, equivalent shear modulus μs, density ρ, etc.The red curve is the reflection coefficient calculated with the parameters in model 1.Fig.4(a)shows the reflection coefficient varied with the squirt fluid factor Kfs. From this figure we can see that when Kfsvaries from 80% to 120%, the reflection coefficient shows apparent change. Thus, we can assume that Kfsis a main contributor to Eq. (31), which means that the estimation of Kfsfrom seismic data is possible.From Fig.4(b)and(e)we can see that,the contributions of μsand ρ to reflection coefficient are very similar and both of the reflection coefficients decrease as the incident angle increases. This phenomenon indicates the great correlation of μsand ρ, so it is difficult for us to extract density from seismic data.However, to get a reliable inversion result only the large contribution is inadequate,such as T(φ)in Fig.4(c).T(φ)is a gain functionwithout no geophysical meaning,being a couple term of squirt flow effect S, porosity φ and Biot coefficient α. Fig. 4(d) shows the reflection coefficient varied with the squirt flow effect S.We can see that although S is a useful parameter for us to describe the subsurface fluid,the contribution of it to reflection coefficient is small.

Table 1 Values of parameters for water-bearing and gas-bearing model.

Furthermore, we apply AVO inversion based on Bayesian framework and incorporate Eq.(31)and seismic wavelet as forward solver to directly estimate the elastic parameters.The constraint of smooth model in objective function is conducive to a more stable result. With the Bayesian inversion theory, we assume that prior distribution obeys the Cauchy distribution.Cauchy distribution is a long-tail probability distribution which can improve the resolution of inversion result. And we assume the likelihood function obeys the Gaussian distribution to obtain the posterior probability density function.Finally,we utilize a method of iteratively reweighted least square to solve the objective function.

Fig. 3. Comparison of different reflection coefficient curves. Curves in blue, black and red denotes the reflection coefficients calculated from the exact Zoeppritz equation, Aki-Richards approximate equation and Eq. (31) respectively. (a) Comparison of reflection coefficient curves of model 1. (b) Difference between reflection coefficients from the exact Zoeppritz equation and Eq.(31)of model 1.(c)Comparison of reflection coefficient curves of model 2.(d)Difference between reflection coefficients from the exact Zoeppritz equation and Eq.(31)of model 2(e)Comparison of reflection coefficient curves of model 3.(f)Difference between reflection coefficients from the exact Zoeppritz equation and Eq.(31) of model 3.

Finally,we use the method of iteratively reweighted least square to optimize and solve the objective equation(Yin et al.,2016;Zong et al., 2018; Ma et al., 2019).

To test the feasibility and practicability of our proposed prestack inversion method, we use a series data modified from well log in an oil field as model parameters. The P-velocity, S-velocity,density and porosity are taken from the well logging data. And squirt fluid factor is calculated from the well log based on the petrophysical theory. Synthetic angle gathers are generated by convolving the model reflection coefficients and 30 Hz Ricker wavelet with exact Zoeppritz equation. Fig. 5 shows the synthetic angle gather data with different signal to noise ratios (S/N). The time window is from 2000 ms to 2800 ms, and the incident angle range is 0°-30°and time sampling interval is 2 ms.Fig.5(a)is the synthetic seismogram profile with no noise. Fig. 5(b) is the synthetic seismogram profile with S/N equal to 5. Fig. 5(c) is the synthetic seismogram profile with S/N equal to 2.

Fig. 6 displays the estimated model parameters from synthetic data.The original squirt fluid factor Kfs,equivalent fluid modulus μs,gain function T(φ),squirt flow effect S and density ρ are displayed in black curves. Red curve displays the inversion result and green curve displays the smooth initial model. From Fig. 6(a), the inversion result of each parameter fits well with the original model parameter in the situation of no noise.When the S/N equals to 5,we still can obtain stable inversion results of Kfsand S as Fig. 6(b)shows. However, the inversion result of density appeared remarkable deviation. It is known that density is difficult to invert accurately,and there are two primary reasons(Kabir et al.,2006).Firstly the contribution of density to reflectivity is small. Secondly the correlation between density and other parameters is strong (Zong et al., 2017). Fig. 6(c) shows the inversion results in the situation of S/N is 2.The error between inverted result of Kfsand real value is moderate so it's a stable parameter to discriminate fluid. What's more, S indicates the squirt effect of pore fluid and it also can be estimated from angle gather data.

Fig.4. Elastic parameters contribution analysis of Eq.(31).Red curve is the reflection coefficient calculated in model 1.Blue curves are reflection coefficient of different parameters varied from 80% to 120%. (a) Reflection coefficient varied with the squirt fluid factor Kfs. (b) Reflection coefficient varied with the equivalent shear modulus μs. (c) Reflection coefficient varied with the gain function T(φ). (d) Reflection coefficient varied with the total squirt flow effect item S. (e) Reflection coefficient varied with the density (ρ).

5. Field data application

We utilize an actual example to investigate the robustness of the proposed pre-stack seismic inversion method, a suite of seismic data from a gulf are used in this section. The survey line passes through two wells(well A and well B).Two reservoirs in well A are both water bearing. The upper formation is cracked but the lower formation is not cracked. Two reservoirs in well A are oil bearing.Seismic data are obtained from the measurements of dual sensor(velocity geophone and pressure geophone)and is processed by the contractor to ensure that the final prestack amplitude imaging underground interface reflection strength should be correct as much as possible. The converted wave, anisotropy effects, and interbed multiples are ignored after processing. Besides, the seismic data has been treated with fidelity processing and amplitude preserved processing (Li et al., 2017; Vitale et al., 2018). The maximum incident angle is around 30°and we perform the partial angle-stack processing with five incident angle ranges, 0°-6°,6°-12°,12°-18°,18°-24°,24°-30°.Five partial angle-stack seismic profiles are shown in Fig. 7. Fig. 7(a) is partial angle-stack seismic profile with incident angle 0°-6°, Fig. 7(b) is partial angle-stack seismic profile with incident angle 6°-12°, Fig. 7(c) is partial angle-stack seismic profile with incident angle 12°-18°,Fig.7(d)is partial angle-stack seismic profile with incident angle 18°-24°,Fig. 7(e) is partial angle-stack seismic profile with incident angle 24°-30°. The time window of seismic data is from 1900 ms to 2200 ms and time sampling interval is 2 ms. The frequency band varies from 5 to 70 Hz, and the main frequency is 27 Hz.

Well A is used in the process of seismic inversion or initial model construction.Two oil bearing reservoirs in well A are near 1970 ms and 2050 ms(the position marked red);the blue position indicates the existence of water sand and white is other thing else. Fig. 8 shows the estimated parameters of field with the proposed method. Fig. 8(a-c) display squirt fluid factor Kfs, squirt flow effect term S and density ρ,respectively.From the figure we can see that,for the overlying oil sand and underlying oil sand,squirt fluid factor appears anomalously low value and squirt flow effect term shows anomalously high value.Besides,density shows low value anomaly at oil sand. In general, the inversion results make the difference between oil layer and dry layer more obvious and show good correlation with the fluid interpretation. The squirt flow effect of medium with fluid filled pores and cracks is very intuitive when the external force acts. And S can effectively reflect this phenomenon under the elastic wave action as Fig.8(b)shows.Squirt fluid factor Kfsis equal to fluid modulus Kfdivided by S,so Kfsshows the lower anomaly when the squirt flow occurs. According to the field data example,the proposed squirt fluid factor shows the effectiveness in fluid discrimination.To ensure the stability of the inversion,firstly,we processed the field seismic data to ensure the quality of seismic data. Furthermore, the parameter to be inverted is a main contributor to reflection coefficient equation by the contribution analysis. Finally, prestack seismic inversion utilized the model constraints and iteratively reweighted least square method to optimize and solve the equation.

Fig. 5. Synthetic angle gather data with different S/N. (a) No noise. (b) S/N = 5 (c) S/N = 2.

Fig. 6. Inversion results of elastic parameters from synthetic data. Red line is inversion result, black line is model data, and green line is smooth initial model. (a) No noise. (b) S/N = 5. (c) S/N = 2.

To test the feasibility of the proposed inversion approach in field data,we use well B to verify the effectiveness of proposed method in field data example. Two water bearing reservoirs in well B are near 1020 ms and 1055 ms(the position marked blue).Fig.9(a)and(b) are the estimation of Russell fluid factor and P-impedance of field data, respectively. From Fig. 9(a) we can see that the Russell fluid factor inversion result shows low value anomaly at both water bearing reservoirs and oil bearing reservoirs, which makes ambiguous fluid discrimination results.In Fig.9(b)we can see that P-impedance shows low value anomaly at upper water reservoir but no obvious anomaly at lower water reservoir. Because the upper reservoir contains cracks, while the lower reservoir does not.The existence of crack in reservoir leads to low value anomaly of Pimpedance. However, the P-impedance itself is insensitive to the fluid,which causes less significantly lower anomaly.In contrast,the squirt flow can make the difference between water bearing reservoir and oil bearing reservoir more obvious by considering the squirt flow effect between cracks and pores.Therefore,according to the contrasts of different inverted fluid factors, the squirt fluid factor is more reliable and feasible to discriminate fluid.

6. Discussion

Russell fluid factor is constructed based on Biot theory, this theory doesn't consider the cracks but only take pores into consideration. And assumption of uniform distribution of pores ignores the influence of squirt flow on wave propagation. In order to more accurately describe reservoir fluid in case of pores and cracks coexist,we build a squirt fluid factor based on Tang's cracked porous medium elastic wave theory. By testing with model parameters, seismic data and well data, we demonstrate that the squirt fluid factor can predict the presence of possible hydrocarbon sand and reduce the illusion of fluid identification.

However,this study has several limitations.First,there are up to five parameters in the AVO inversion so that the prediction accuracy and stability is still need to be improved.To solve this problem,we can try to develop more stable inversion algorithm or calculate more reasonable low-frequency initial model in AVO inversion by broadband inversion method, etc. (Zong et al., 2018). Second, how to reveal the multi-frequency information in fluid factor as much as possible remains challenging in the future study. In a word, the prime objective of this paper is to estimate the squirt fluid factor from prestack seismic data and we think that the goal is achieved.We construct a squirt fluid factor based on the cracked porous medium elastic wave theory,which can lead to more reliable fluid discrimination result in seismic exploration.

Fig. 7. Partial angle-stack seismic profiles with different incident angle ranges. (a) Partial angle-stack seismic profile with incident angle 0°-6°. (b) Partial angle-stack seismic profile with incident angle 6°-12°.(c)Partial angle-stack seismic profile with incident angle 12°-18°.(d)Partial angle-stack seismic profile with incident angle 18°-24°.(e)Partial angle-stack seismic profile with incident angle 24°-30°.

Fig.8. Estimation of parameters of field data with the proposed method.(a)Squirt fluid factor.(b)Squirt flow effect term.(c)Density.Red position on well A is oil and blue position on well A is water.

Fig. 9. Estimation of parameters of field data. (a) P-impedance. (b) Russell fluid factor.

7. Conclusion

Combining the unified theory for elastic wave propagation through porous media containing cracks and petrophysical theory,we develop a novel AVO pre-stack seismic inversion method for fluid discrimination.A novel fluid indicator considering squirt flow effect is constructed. Based on the squirt fluid factor, we derive a new reflection coefficient equation.The precision analysis confirms the effectiveness of the reflection coefficient equation. The elastic parameters contribution analysis of reflection coefficient equation demonstrates that the squirt fluid factor can be effectively extracted from the seismic data.The consideration of squirt flow effect in the proposed method can diminish the ambiguity of fluid discrimination and the Bayesian frame improves the stability of inversion method. The model test verifies the feasibility and field data example illustrates the practicability of this AVO inversion approach.

Acknowledgements

We would like to acknowledge the sponsorship of National Natural Science Foundation of China (41974119, 42030103) and Science Foundation from Innovation and Technology Support Program for Young Scientists in Colleges of Shandong Province and Ministry of Science and Technology of China (2019RA2136) and Marine S&T Fund of Shandong Province for Pilot National Laboratory for Marine Science and Technology (Qingdao)(2021QNLM020001-6).